H Beam Cutting Machine BEAMCUT 800 | Portable Gas Cutter for Web and Flange

BEAMCUT 800
H-beam gas cutting machine • Oxy-fuel • Model BEAMCUT 800

Web and flanges. One clean line through the beam.

The CRUXWELD BEAMCUT 800 is a portable H-beam cutting machine for structural steel. Its rail clamps across the beam, a second drive runs the oxy-fuel torch up the first flange, the powered carriage carries it across the web, and the drive brings it down the second flange, so the whole section is cut along one line. It cuts 5 to 50 mm steel, square, slanted or bevelled up to 30°.

800 mmWeb cutting span
400 mmFlange cutting span
5–50 mmCutting thickness
21.5 kgMachine body
↕

Two powered drivesOne for the web, one for the flanges, 50 to 750 mm/min
🔥

Acetylene or propaneG02 or G03 cutting tips, sizes 1, 2 and 3 supplied
💬

WhatsApp + video supportSet-up help from our technical team

Price, delivery & technical help — get a fast response.

Overview

How it works

Up one flange, across the web, down the other

An H-beam has a web, the plate in the middle, and two flanges, the plates on either side. Cut by hand, that is three separate cuts that rarely line up. The BEAMCUT 800 makes all three from one rail position.

How the BEAMCUT 800 cuts an H-beam: up the first flange, across the web, then down the second flangeEND VIEWWEBFLANGE 1FLANGE 2RAILTHE CUT ON THE BEAM1CUT THE FIRST FLANGETorch horizontal, 7 to 10 mm from the flange.The vertical drive takes it up the flange.2CUT THE WEBTorch turned to vertical. The carriagetravels along the rail, across the web.3CUT THE SECOND FLANGETorch horizontal again, outside the far flange.The drive takes it down to the limit switch.✓CUT COMPLETEBoth flanges and the web are cut throughalong one line. The end piece comes away.FLANGE 1WEBFLANGE 2
⚙

Clamp the rail across the beamThe fixed pressure plate grips one flange and the movable plate the other. Mount the machine, light the torch and set the flame once on the quick distributor.
1

Cut the first flangeTorch horizontal, 7 to 10 mm from the flange, starting just below its lower edge. The vertical drive takes it up; ease the speed where the flange meets the web.
2

Cut the webRaise the torch, turn it to vertical, 7 to 10 mm above the web. Engage the clutch and the carriage travels along the rail.
3

Cut the second flangeTurn the torch horizontal again and move outside the far flange. The drive takes it down; a limit switch stops it and shuts off cutting oxygen.
Watch it work

H-beam cutting in action

From the CRUXWELD Tech channel

See it cut a steel beam on site

The rail is clamped across the beam, the carriage travels at a set speed and the torch works through the section.

  1. Rail clamped across the beam
  2. Powered travel at a steady speed
  3. Both flanges and the web on one line
Play video
BEAMCUT 800 H-beam cutting machine cutting a flange with sparksTorch horizontal, cutting through the flange.
Built part by part

Watch the BEAMCUT 800 come together

Seven assemblies, shown on the machine in the order they go on. Each one is highlighted on the photo with a close-up beside it.

1. Rail2. Carriage and web drive3. Control panel4. Vertical bar5. Torch and cutting tip6. Quick gas distributor7. Hoses and cables
PART 1 OF 7

Rail and clamps on the beam

The 1500 mm rail lies across the beam. A fixed and a movable pressure plate clamp it to the flanges with butterfly screws.

PART 2 OF 7

Carriage and web drive

Aluminium body with the web-cutting motor, reducer and clutch. It rides the rail on four rollers at 50 to 750 mm/min.

PART 3 OF 7

Control panel

Everything is worked from here: the four-way switch for direction, quick-return button, speed knob and power switch.

PART 4 OF 7

Vertical bar and flange drive

A second motor drives the torch up and down on a rack, to cut the flange. Limit switches stop it at the end of travel.

PART 5 OF 7

Torch and cutting tip

Oxy-fuel torch on an adjustable holder; it tilts for bevels of 0 to 30°. G02 tips for acetylene or G03 for propane.

PART 6 OF 7

Quick gas distributor

Set the flame once. After that one knob takes it from off to preheat to cutting, so the flame is not re-adjusted for every cut.

PART 7 OF 7

Hoses and cables

Gas hoses run from the distributor to the torch in a high loop that follows the torch as it travels.

✓ COMPLETE

BEAMCUT 800, ready to cut

21.5 kg machine body on a 1500 mm rail. Connect AC 220 V, oxygen and fuel gas, and cut the web and both flanges.

800 mmweb cutting span
400 mmflange cutting span
5–50 mmcutting thickness
0–30°bevel angle
Parts diagram

Every part, named

The ten main parts. The numbers on the photo match the list beside it.

BEAMCUT 800 H-beam cutting machine with 10 numbered parts12345678910
1TorchCarries the cutting tip; tilts for bevels.
2Gas hosesDeliver gas from the distributor to the torch.
3Transverse adjusting wheelMoves the torch sideways to line the tip up with the mark.
4Rail1500 mm track the carriage travels on.
5Vertical moving barCarries the torch up and down for flange cutting.
6Geared drive motorMotor and reduction gear for powered travel.
7Quick gas distributorSet the flame once; one knob for off, preheat and cutting.
8HandleFor carrying and placing the machine.
9Rail pressure platesClamp the rail to the beam flanges.
10Clutch knobEngages or releases the web drive.
Why fabricators pick it

What the BEAMCUT 800 does for a structural shop

BEAMCUT 800 H-beam cutting machine: The whole section from one rail position

Three cuts, one lineThe whole section from one rail positionBoth flanges and the web are cut without moving the rail, so the three cuts meet. Powered travel keeps the speed steady from start to finish.
BEAMCUT 800 H-beam cutting machine: Set the flame once

Quick distributorSet the flame onceOne knob takes the torch from off to preheat to cutting.
BEAMCUT 800 H-beam cutting machine: All movement from one place

One control panelAll movement from one placeFour-way switch, quick return, speed knob and power switch.
BEAMCUT 800 H-beam cutting machine: Fixed to the beam in a minute

Rail clampsFixed to the beam in a minuteFixed and movable pressure plates grip the flanges.
BEAMCUT 800 H-beam cutting machine: Weld preparation included

Bevel and slant cutsWeld preparation includedBevels of 0 to 30° on web and flange.
Carried to the beam, not the other way roundAluminium body with the rail packed separately. It works on the beam where it lies, in the shop or on site.
21.5 kgmachine body
1500 mmrail
AC 220 Vsupply
Will it fit your beam

Web, flange and angle limits

Steel H-beam showing the web cut and the two flange cuts in red
800 mmWeb cutting span, maximum
400 mmFlange cutting span, maximum
5–50 mmSteel thickness
0–30°Bevel on web and flange
35°Slant cut across the web, cut length up to 1300 mm
30°Slant cut on the flange, cut height up to 690 mm
Tip to steel while cutting: 8–10 mm with acetylene • 5–8 mm with LPG
Applications

Where a beam cutter earns its keep

🏗

H-beams and I-beamsCutting beams to length for structural fabrication.
🏢

Columns and raftersSquare and slanted ends for building frames.
📐

Weld preparationBevelled ends on web and flange, ready for welding.
🏭

Structural workshopsRepeat cuts at a steady, set speed.
🚧

Site workCuts the beam where it lies; nothing to lift onto a saw.
🛠

Fabrication yardsCutting stock beams to the lengths a job needs.
Good practice

Getting a clean cut

Keep the rail groove clean; dirt in it shows up in the cut.
Check the drive switch is in the middle, stop position before switching the power on.
Let the machine come to a full stop before changing direction.
Never move the machine with the preheat flame lit.
Check gas connections with soapy water; never use oil or grease on oxygen fittings.
Earth the machine through its power cable, and do not use it outdoors in wet weather.
Pairs with

More from the gas cutting range

The BEAMCUT 800 cuts beams. These cut the plate, the circles and the pipe openings.

Tell us the beam. We will confirm the set-up.

Send the beam size, web and flange thickness, cutting angle and fuel gas. Our technical team replies on WhatsApp with suitability, price and delivery.

Specifications

BEAMCUT 800 Technical Data

H-beam gas cutting machine

General
Model
BEAMCUT 800
Type
Portable H-beam gas cutting machine
Process
Oxy-fuel flame cutting
Body
Aluminium
Cutting
Web cutting span
800 mm maximum
Flange cutting span
400 mm maximum
Cutting thickness
5 – 50 mm
Bevel angle
0 – 30° (web and flange)
Slant cut, web
Up to 35°, cut length up to 1300 mm
Slant cut, flange
Up to 30°, cut height up to 690 mm
Cutting tips
G02 (acetylene) or G03 (propane)
Drive
Cutting speed
50 – 750 mm/min
Speed control
SCR control
Web drive motor
110 V, 50 Hz, 30 W, 3600 rpm
Flange drive motor
110 V, 50 Hz, 40 W, 2200 rpm
Power source
AC 220 V ±10%
Size
Dimensions, body
250 × 176 × 260 mm
Dimensions, rail
224 × 114 × 1500 mm
Weight, body
21.5 kg
Weight, rail and accessories
15.5 kg

The 110 V ratings are the internal drive motors; the machine is supplied from AC 220 V. Cutting spans are the reach in each direction, so check the full beam dimensions and torch clearance for your section. For carbon and mild steel suited to oxy-fuel cutting. Specifications as published by CRUXWELD.

Accessories

Scope of supply

What comes with the machine

BEAMCUT 800 spanners, cutting tips and power cable
  • 1BEAMCUT 800 machine body with control panel and quick gas distributor
  • 2Flange cutting mechanism with vertical bar, and standard torch
  • 3Rail, 1500 mm, with fixed and movable pressure plates
  • 4Cutting tips G02 or G03, sizes 1, 2 and 3
  • 5Inlet gas connection and power cable
  • 6Spanner, M5 hexagon key, Phillips screwdriver and tip-cleaning needle
  • 7Instruction manual and certificate
Tell us when ordering: acetylene (G02 tips) or propane (G03 tips). Not included: gas cylinders, regulators, supply hoses and flashback arrestors.

Description

About the product

BEAMCUT 800 H-beam gas cutting machine

The CRUXWELD BEAMCUT 800 is a portable H-beam cutting machine that cuts the web and the flanges of structural steel sections with an oxy-fuel torch. A 1500 mm rail clamps across the beam, a vertical mechanism carries the torch up the first flange, the carriage travels along the rail on four rollers to cut the web, and the torch then comes down the second flange. Steel from 5 to 50 mm thick is cut at a set speed of 50 to 750 mm/min.

The machine reaches 800 mm across the web and 400 mm down the flange. Both cuts can be bevelled from 0 to 30° for weld preparation, and the rail can be set at an angle for slant cuts of up to 35° across the web.

Controls that keep the cut repeatable

All movement is worked from one panel: a four-way switch for the web and flange drives, a quick-return button, a speed knob and the power switch. The quick gas distributor holds the flame setting, so the operator switches between off, preheat and cutting with one knob. Cutting oxygen is interlocked with travel, and limit switches stop the flange drive at the end of its stroke.

Built to be carried

The body is aluminium, weighs 21.5 kg and measures 250 × 176 × 260 mm; the rail and accessories add 15.5 kg. It runs on AC 220 V with G02 tips for acetylene or G03 tips for propane.

The BEAMCUT 800 sits in the Gas Cutting range beside the GLIDO 2T plate cutting machine, the ORBICUT 600 pipe hole cutter and the CIRCO 600 circle cutting machine. Our technical team helps with set-up on WhatsApp and video call.

Question & Answers

FAQ

H-Beam Cutting Machine — Frequently Asked Questions

▸What is the BEAMCUT 800 used for?
Cutting the web and flanges of steel H-beams and similar structural sections with an oxy-fuel torch, square, slanted or bevelled.
▸What size of beam can it cut?
It reaches up to 800 mm across the web and up to 400 mm down the flange. Send us the full beam dimensions and we will confirm the rail position and torch clearance.
▸What thickness can it cut?
Steel from 5 to 50 mm thick, with the tip size chosen for the thickness.
▸Can it cut bevels and angled ends?
Yes. Bevels of 0 to 30 degrees on both web and flange, slant cuts up to 35 degrees across the web and up to 30 degrees on the flange.
▸How fast does it cut?
Travel speed is adjustable from 50 to 750 mm/min on the speed knob. The quick-return button runs the drives at full speed for repositioning.
▸Is it a CNC machine?
No. Travel is powered and the operator sets up and controls the cut from the panel. There is no programming.
▸Does it run on acetylene or propane?
Either. G02 tips are for acetylene and G03 tips for propane. Tell us your fuel gas when ordering.
▸What materials is it for?
Carbon and mild steel, the steels that oxy-fuel cutting suits. It is not for stainless steel or aluminium.
▸What power supply does it need?
AC 220 V, plus or minus 10 percent, with an earthed supply.
▸How heavy is it?
The machine body weighs 21.5 kg and the rail with accessories 15.5 kg.
▸How do I get a quotation?
Send the beam size, web and flange thickness, cutting angle and fuel gas on WhatsApp to +91 88008 82983. Our technical team replies with suitability, price and delivery.

Leave a comment

Your email address will not be published. Required fields are marked *

H Beam Cutting Machine BEAMCUT 800 | Portable Gas Cutter for Web and Flange

WhatsApp chat