Magnetic Pipe Cutting Machine

TUBOCUT GECKO
Magnetic pipe cutting machine • Model TUBOCUT GECKO

Grips the pipe by magnet. Cuts it square or bevelled.

Formerly sold as TUBOCUT-MS — same machine, new name

The CRUXWELD TUBOCUT GECKO crawls around steel pipe on double permanent-magnet wheels — no chain to fit, no track to bolt on. Set the speed, flick the switch, and the torch cuts a clean circumferential, longitudinal or 45° bevel edge on pipe from 100 mm diameter upward.

Ø 100 mm+Pipe diameter
5–100 mmWall thickness
0–45°Bevel angle
20 kgCarry weight
✅

Spares in stockNozzles, torch, clamp, cable — shipped from our factory
💬

WhatsApp + video supportSetup and cut-quality help from our technical team
🏭

ISO-certified OEMGeM-registered Indian manufacturer since 1997
Need a chain-driven or manual pipe cutter instead? TUBOCUT PYTHON • TUBOCUT KOALA

Price, delivery & technical help — get a fast response.

Overview

How it works

One pass around the pipe. No chain, no rail.

Permanent magnets in the roller wheels hold the carriage to the pipe wall at any angle — horizontal, vertical, even upside down. The motor drives the wheels, the torch follows at a fixed height, and the cut comes out straight.

TUBOCUT GECKO held on a steel pipe by its magnet wheels

Permanent-magnet wheels
Oxy-fuel cutting torch
Speed dial + direction switch
01

Place it on the pipeThe magnet wheels pull the 20 kg carriage onto the steel and hold it there. No clamps, no chain length to measure.
02

Set torch and angleSlide the torch bar to the cut line, tilt the holder 0–45° for a weld bevel, set nozzle height with the hand wheel.
03

Dial in the speedSCR speed control from 50 to 1150 mm/min on the dial, forward or reverse on the switch.
04

Let it crawlThe carriage travels the circumference and cuts in one continuous pass — square, bevelled or along the pipe axis.
Built for site work

What makes the GECKO different

Double permanent-magnet wheels
Permanent magnets

Double permanent-magnet wheels

Four magnetic rollers grip the pipe without power. The carriage stays put when the motor stops, and it runs on any pipe over 100 mm.

Speed dial and forward / reverse switch
Control

Speed dial and forward / reverse switch

SCR speed control from 50 to 1150 mm/min on a 0–10 dial. Flick the switch to reverse direction for a second pass or to back off the cut.

Injector-type cutting torch
Oxy-fuel torch

Injector-type cutting torch

Three-hose injector torch with gas distributor and flow valves on the carriage. Cuts 5–100 mm wall with the right nozzle.

Plasma torch mounts in the same clamp
Plasma ready

Plasma torch mounts in the same clamp

Swap the gas torch for a machine plasma torch in the torch clamp and run the GECKO with a CRUXWELD FINELINE plasma source for thinner, faster cuts.

Carry handles on both sides
Compact

Carry handles on both sides

A 20 kg carriage with grab handles front and rear, plus a separate control box with its own carry handle. One person moves it between cuts.

0-45 deg weld-prep bevel
Bevel

0–45° weld-prep bevel

Tilt the torch holder and the GECKO cuts the bevel in the same pass as the parting cut — a pipe end ready for fit-up without grinding.

Cut types

Four cuts, one machine

Circumferential cut

Parting cut around the pipe — the standard job.

Longitudinal cut

Straight cut along the pipe axis to split or slot the pipe.

Bevel cut

Square or up to 45° bevel for weld preparation.

Circular cut-out

Round openings for branches and nozzles on the pipe wall.

In action

From the fabrication shop to the pipeline trench

TUBOCUT GECKO: Large-diameter pipe, fabrication shopLarge-diameter pipe, fabrication shop
TUBOCUT GECKO: Pipeline site, outdoorsPipeline site, outdoors
TUBOCUT GECKO: Guide band on a pipeline sectionGuide band on a pipeline section
TUBOCUT GECKO: Oxy-fuel parting cutOxy-fuel parting cut
TUBOCUT GECKO: Magnets hold it on the pipeMagnets hold it on the pipe
TUBOCUT GECKO: Torch at the cut lineTorch at the cut line
Videos

See the GECKO cut

Cutting inside a large pipe on site

Magnets hold the carriage on the inside wall while it cuts.

Vertical tank shell on the guide band

Optional pipe guide band keeps the cut line true on vertical work.

Play video

No chain. Just cut.

60-second look at the magnet drive, from the CRUXWELD Tech channel.

Play video

Full demo: oxy-fuel and plasma cutting on pipe

Setup, speed setting and cut quality with both torches, from the CRUXWELD Tech channel.

TUBOCUT GECKO component overview with 13 labelled parts
Anatomy

Every part, labelled

Thirteen components, numbered on the illustration.

  1. 01Machine body
  2. 02Cross-feed handwheel — horizontal torch position
  3. 03Gas hoses — preheat O2, fuel gas, cutting O2
  4. 04Cutting torch
  5. 05Torch adjustment handwheel
  6. 06Carry handle
  7. 07Direction switch — forward / stop / reverse
  8. 08Heat shield
  9. 09Flow control valves
  10. 10Gas distributor — three gas supplies
  11. 11Speed control knob
  12. 12Electrical socket
  13. 13Magnetic roller wheels — guide the carriage on the pipe
TUBOCUT GECKO product dimensions for the cutting carriage, magnetic roller and power control box
Size and weight

Fits in the back of a car

The carriage body is about 230 × 150 × 170 mm and the control box 200 × 100 × 170 mm. With the torch bar and torch fitted the machine measures 350 × 310 × 280 mm and weighs 20 kg.

↔

Magnetic rollers 70 × 30 mmFour rollers, permanent magnets, no power needed to hold.
⚡

220 V / 110 V single phaseRuns from a wall socket or a small site generator.
⚖

20 kg carriageOne-person lift with handles on both sides; control box carried separately.
Optional accessory

Pipe Guide Band

For large-diameter pipe, vertical columns and tank shells, the guide band gives the GECKO a fixed track to ride on. The perforated steel band wraps the pipe, the mounting blocks and adjustable supports carry the carriage, and a tension screw pulls it tight.

  • Fixed cut line on long circumferences where a free-crawling carriage could drift
  • Vertical and overhead work on columns, risers and storage-tank shells
  • Adjustable supports set stand-off and keep the torch square to the wall
  • Supplied as a kit with band, mounting blocks, supports, tension adjuster and fasteners
Pipe guide band assembly: band, supports, tension adjuster and mounting blocksTUBOCUT GECKO cutting a vertical pipe on the guide band
TUBOCUT GECKO running on the optional pipe guide band
Choose your TUBOCUT

GECKO, PYTHON or KOALA?

Three pipe cutters, three ways to hold on to the pipe. Pick by how the machine grips and whether you have power at the cut.

TUBOCUT GECKOTUBOCUT PYTHONTUBOCUT KOALA
Grip on pipePermanent-magnet wheels — no chainChain wrapped around the pipeChain wrapped around the pipe
DriveMotorised, forward / reverseMotorised, chain-drivenManual hand wheel — no electricity
Pipe diameter100 mm and up100 mm and up100 mm and up
Wall thickness5–100 mm5–100 mm5–50 mm
Bevel0–45°Up to 45°0–45°
TorchOxy-fuel or plasmaOxy-fuel or plasmaOxy-fuel
Best forFast setup on any steel pipe, longitudinal cuts, inside-wall cutsProduction cutting where a chain track is already the routineSites without power, occasional cuts, lowest cost
This pageSee TUBOCUT PYTHON →See TUBOCUT KOALA →
Applications

Where the GECKO earns its keep

🔧

Pipe fabrication shopsParting and bevelling pipe spools before fit-up and welding.
🏭

Pipeline and cross-country workCutting line pipe in the trench or on skids, with the control box on the bank.
⛽

Oil, gas and refinery maintenanceRemoving and replacing sections of process piping in position.
🏭

Storage tanks and vesselsShell cuts and nozzle openings on tank plate — the magnets hold on vertical and curved surfaces.
🚧

Structural and pilingCutting tubular piles and columns to length on site.
💧

Water and utility pipeSteel water mains and penstock sections, square or bevelled.

Tell us your pipe size. We will confirm the nozzle and the cut.

Send the pipe OD, wall thickness and whether you cut with oxy-fuel or plasma. Our technical team replies on WhatsApp with the right setup and a quotation.

For this job, consider

Need a branch opening, not a cut-off? ORBICUT 600 pipe hole cutter.

This machine cuts pipe to length. For the round opening a branch pipe fits into, the ORBICUT 600 sits on the pipe and cuts it in one pass, with the bevel if you need one.

Holes Ø80–600 mm5–50 mm steelBevel 0–45°Follows the pipe curve

Specifications

TUBOCUT GECKO Technical Data

Magnetic pipe cutting machine

General
Model
TUBOCUT GECKO
Previous model name
TUBOCUT-MS
Type
Magnetic pipe cutting machine (portable, motorised)
Drive method
Motorised, double permanent-magnet wheels
Direction
Clockwise / anti-clockwise (forward / reverse switch)
Cutting
Effective pipe diameter
100 mm onwards
Cutting thickness (wall)
5 – 100 mm
Cutting shape
Square and bevel; circumferential, parallel (longitudinal), end-face and circular cuts
Cut / bevel angle
Variable up to 45°
Cutting speed
50 – 1150 mm/min
Speed control
SCR; adjustment by dial
Cutting torch
Injector type (oxy-fuel); plasma torch mountable
Electrical
Input voltage
AC 220 V / 110 V, 50/60 Hz, single phase
Motor power
70 W
Inverter power
158 W
Physical
Dimensions (L × W × H)
350 × 310 × 280 mm
Weight
20 kg
Optional
Pipe guide band kit; machine plasma torch

Specifications as published by CRUXWELD. Dimensions on the illustration above are for the carriage body and control box individually and are approximate.

Accessories

Scope of supply

What comes in the box

TUBOCUT GECKO scope of supply: carriage, torch, control box, cable, nozzles and wire rope
  • 1TUBOCUT GECKO cutting carriage with double permanent-magnet wheels and carry handles
  • 2Power control box with on/off switch, fuse and carry handle
  • 3Power cable with locking connector
  • 4Injector-type oxy-fuel cutting torch with torch clamp, gas distributor and hoses
  • 5Cutting nozzles — set of 3
  • 6Wire rope with anchor for circumferential guiding
Optional: Pipe guide band kit (band, mounting blocks, adjustable supports, tension adjuster) • machine plasma torch for use with a CRUXWELD FINELINE plasma source.
Spares

Spares we keep in stock

TUBOCUT GECKO components and spares: machine body, control box, power cable, cutting torch, nozzle, torch clamp, wire rope, potentiometer, rail assembly

Machine body, power control box, power cable, cutting torch, cutting nozzles, torch clamp and connector, wire rope, speed potentiometer and rail assembly are all available as spares from CRUXWELD.

Description

About the machine

TUBOCUT GECKO magnetic pipe cutting machine

The CRUXWELD TUBOCUT GECKO is a portable, motorised magnetic pipe cutting machine for steel pipe from 100 mm diameter upward. Instead of a chain or a bolted track, the carriage runs on double permanent-magnet wheels that hold it to the pipe wall in any position. That removes the longest part of a conventional pipe-cutter setup: there is no chain to size, wrap and tension before every cut.

With the standard injector-type oxy-fuel torch the GECKO cuts wall thickness from 5 to 100 mm. Travel speed is set on an SCR dial between 50 and 1150 mm/min, and a switch reverses the direction of travel. The torch holder tilts to 45°, so a weld bevel is cut in the same pass as the parting cut. Because the magnets grip anywhere on the steel, the same machine also makes longitudinal cuts along the pipe axis, circular openings for branches, and cuts on the inside wall of large pipe.

Oxy-fuel or plasma

The torch clamp accepts a machine plasma torch. Paired with a CRUXWELD FINELINE plasma cutting source, the GECKO cuts thinner wall faster and with less heat input; with oxy-fuel it handles thick wall up to 100 mm. Both setups are shown in the demonstration video above.

Pipe guide band for large and vertical work

On very large circumferences, vertical columns and storage-tank shells, the optional pipe guide band gives the carriage a fixed track. The perforated band wraps the pipe, mounting blocks and adjustable supports carry the carriage, and a tension adjuster pulls the band tight. The result is a cut line that stays true all the way round.

Power and portability

The carriage weighs 20 kg and has grab handles on both sides. A separate power control box with its own carry handle runs from 220 V or 110 V single phase, so the GECKO works in the shop and on site from a small generator. Spares — nozzles, torch, clamp, cable, potentiometer and wire rope — are stocked at CRUXWELD, and our technical team supports every machine on WhatsApp and video call.

Model note: the TUBOCUT GECKO was previously sold as the TUBOCUT-MS. Specifications, spares and accessories are unchanged.

Video

Play video
Play video
Play video

Question & Answers

01

Magnetic Pipe Cutting Machine — Frequently Asked Questions

How is a magnetic pipe cutting machine different from a chain-driven one?
A chain cutter is tied to one circumferential path around the outside of the pipe. The TUBOCUT GECKO holds on with permanent-magnet wheels, so besides circumferential cuts it can run lengthwise along the pipe, around an end face, on the inside of a large shell and cut circular openings — with no chain to fit or tension.
What pipe sizes and wall thickness can it cut?
Steel pipe from 100 mm diameter upwards, with wall thickness from 5 mm to 100 mm using the oxy-fuel torch. With a plasma torch mounted, thickness depends on the plasma cutter’s rating.
Can it cut a bevel?
Yes. The torch holder tilts to any angle up to 45° for single-V weld preparation in the same pass as the cut.
Will the magnets hold on a curved pipe?
Yes. The machine has permanent-magnet wheels at both front and rear, which keep it stable on curved and flat steel. Permanent magnets need no power, so a supply interruption does not release the machine.
Does it work with plasma as well as oxy-fuel?
Yes. The TUBOCUT GECKO is designed for both; the plasma torch is mounted in place of the gas torch.
What power supply does it need?
220 V or 110 V, 50/60 Hz, for the 158 W inverter that feeds the 70 W drive motor — a small site generator is sufficient. The cutting energy comes from the gas or plasma supply.
Can it cut on the inside of a pipe or shell?
Yes, provided the diameter is large enough for the machine (350 × 310 × 280 mm) to sit on the inner wall. This is a common use on vessels and penstocks.
How do I get the price and delivery time?
Request a quote on this page or message +91 88008 82983 on WhatsApp with your pipe diameters, wall thickness and process (gas or plasma). You will receive a GST quotation with delivery time, usually the same working day.
Outside, inside or along the pipe? Tell us the job and we will confirm the machine.

0 replies on “Magnetic Pipe Cutting Machine”

WhatsApp chat