ID mounted pipe beveling machine · Pipe ID 80–240 mm
Lock It Inside the Bore. Cut a True Weld Bevel on 3″–10″ Pipe.
The CRUXWELD BEVO 240 is a portable ID mounted pipe beveling machine for pipe with an inside diameter of 80 to 240 mm and walls up to 20 mm. An expanding mandrel locks it inside the bore and centres it on the pipe, an 1800 W motor turns the tool head at a slow, steady 16 r/min, and the feed handwheel takes the tool bit into the pipe end. The result is a cold, machined 0°, 30° or 37.5° end prep, square to the pipe and ready for the root pass.
80–240 mm
Pipe ID
20 mm
Max wall
1800 W
Motor
37.5°
Std bevel
▶ Watch it work
Stop Grinding Pipe Bevels
✓Mandrel locks inside the bore and centres the machine
✓Tool head turns around the pipe end, the handwheel feeds the bit
ID Mounted Pipe Beveling Machine for 80–240 mm Pipe
A good butt weld on pipe starts with an end prep that is square to the pipe, at the right angle, with an even root face. A grinder cannot hold that all the way round, and a gas-cut bevel needs grinding back to clean metal. The BEVO 240 ID mounted pipe beveling machine machines the end instead. Because it centres on the bore, the bevel runs concentric with the pipe and the outside surface stays free for the tool head.
It is made for pipe spool shops, power and process plant maintenance, pipelines and pressure-part fabrication, where pipe from 3″ to 10″ has to be prepared joint after joint. One operator sets the mandrel, fits the tool bit and feeds the cut. For small-bore boiler tubes, see our BEVEX 63 pipe beveling machine.
Pipe ID 80–240 mm
Expansion jaw sets cover the full 3″–10″ range in one machine.
Walls up to 20 mm
Standard and heavy-schedule pipe in its size range.
0°, 30° and 37.5°
Facing and the two common weld bevels, with standard tool bits.
Cold machining
Chips, not sparks: no heat-affected edge, no oxide to grind off.
CRUXWELD BEVO 240 ID mounted pipe beveling machine.
02
The principle
Why Mounting Inside the Bore Gives a Truer Bevel
Section through the pipe end: the mandrel expands against the bore, the tool head turns around it and machines the bevel.
The mandrel slides into the pipe and its expansion jaws are drawn out against the inside wall until the machine is locked and centred on the bore. The tool head then rotates around that centre line, so the bevel and the root face are cut concentric with the pipe, even if the outside surface is out of round or carries coating.
✓Self-centring on the bore — no packing, no shims
✓Outside of the pipe stays free, so the head clears supports and racks
✓The same angle and root face on every joint
✓Facing the pipe end square is done in the same set-up
03
How it works
Four Steps to a Weld-Ready Pipe End
STEP 1
Set the mandrel
Fit the expansion jaw set that matches the pipe ID and slide the mandrel into the bore.
STEP 2
Fit the tool bit
Clamp the 0°, 30° or 37.5° tool bit in the tool holder for the end prep you need.
STEP 3
Lock and cut
Tighten the mandrel to lock on the bore, start the 1800 W motor and turn the feed handwheel to take the tool into the wall.
STEP 4
Check and weld
Back the tool off, release the mandrel and lift the machine out. The pipe end is ready for fit-up.
04
Why fabricators choose it
What a Machined End Prep Changes on the Job
01
No grinder bevels
A hand-ground bevel changes with every operator. The BEVO 240 cuts the same angle and root face on every joint.
02
Fewer root repairs
An even groove and constant root face give the welder a steady gap for a sound root pass.
03
No heat, no scale
Gas-cut ends leave oxide and a heat-affected edge. A machined bevel is bright metal, ready to weld.
04
Goes to the pipe
Clamps inside the pipe where it lies — on a rack, in a trench or on site — instead of moving pipe to a lathe.
05
One machine, 3″–10″
Change the jaw set, not the machine, across the 80–240 mm ID range.
06
Runs on 220 V
A single-phase 220 V, 50 Hz socket on site or in the shop is all it needs.
05
Key features
ID Mounted Pipe Beveling Machine Features
01
Self-centring expanding mandrel
Locks square to the bore in seconds for a concentric bevel.
02
80–240 mm in one machine
Expansion jaw sets cover the full 3″–10″ ID range.
03
Walls up to 20 mm
Handles standard and heavy-schedule pipe in its size range.
04
Three standard tool bits
0° for facing, 30° and 37.5° for the common weld bevels.
05
1800 W motor
Strong torque at a slow 16 r/min spindle speed for a smooth finish.
06
Feed handwheel
Controlled, step-by-step feed of the tool bit into the pipe end.
07
Rigid tool head
Two-arm tool holder keeps the bit steady through the cut.
08
Two carry handles
Easy to position on the pipe and steady while it runs.
06
Know your machine
BEVO 240 Main Parts
Five parts do the work. The motor on top drives the cutter spindle, the feed handwheel advances the tool bit, the two handles position and steady the machine, and the tension block on the mandrel expands the jaws to lock the machine in the bore.
Rigid two-arm tool head
CE marked
✓Use the jaw set that matches the pipe ID
✓Keep the power cable clear of the cutting area
✓Wear eye and ear protection while cutting
07
Tooling
Tool Bits Supplied as Standard
0°
Facing
Squares the pipe end and cuts the root face (land).
30°
Bevel
A common bevel for butt welds on many pipe joints.
37.5°
Bevel
The standard pipe weld bevel used on most piping jobs.
Need a different angle, a J-prep or a counterbore? Tell our technical team the joint you need when you enquire.
08
Applications
Where the BEVO 240 Pipe Beveling Machine Is Used
Power plants
Pipe replacement and modification during shutdowns.
Refinery & petrochemical
Process pipe in maintenance and turnaround work.
Pipelines
End prep of line pipe joints in the field.
Pipe spool fabrication
Shops preparing joint after joint on 3″–10″ pipe.
Pressure parts & vessels
Nozzles and pipe connections on vessels and headers.
Shipbuilding & marine
Ship piping where access around the pipe is tight.
✓BEVO 240 ID mounted pipe beveling machine with 1800 W motor
✓Expanding mandrel with expansion jaw sets for 80–240 mm ID
✓Standard tool bits: 0°, 30° and 37.5°
✓Tool kit in a carry box
✓Packed in a wooden crate for safe transport
The exact scope is confirmed on the quotation. Ask for spare tool bits and extra jaw sets with your order. See the full range of welding and cutting equipment.
Packed in a wooden crate with the tool box.
10
Why buy from CRUXWELD
Based in India. Supported Worldwide.
45+ years of welding expertise
Application advice from people who weld. Our technical team answers on WhatsApp and video call.
ISO 9001 certified company
Every machine is inspected and test-run before dispatch.
GeM Registered OEM Manufacturer
Tender-ready documentation for government, PSU and institutional buyers.
Pan-India supply, export ready
Dispatched across India and exported, with tool bits and jaw sets on request.
BEVO 240 ID Mounted Pipe Beveling Machine — Technical Data
PARAMETER
BEVO 240
Model
BEVO 240
Type
ID mounted pipe beveling machine, expanding mandrel
Pipe inside diameter
80 mm – 240 mm (3″ – 10″)
Max wall thickness
20 mm
Motor power
1800 W
Power supply
220 V, 50 Hz, single phase
Spindle speed
16 r/min
Tool feed
Feed handwheel
Standard tool bits
0° (facing), 30° and 37.5° (bevel)
Operations
External bevel, facing, squaring the pipe end
Materials
Carbon steel, stainless steel, alloy steel pipe
Clamping
Expansion jaw sets covering 80 mm – 240 mm ID
Process
Cold machining, no heat input
Certification
CE marked
Bevelled pipe ends, ready for fit-up.
Reading the specification
Pipe inside diameter is the bore the mandrel locks into: 80 to 240 mm. Max wall thickness is the heaviest wall it bevels: 20 mm. The tool bits set the end prep, and the 1800 W motor on 220 V single phase runs from any workshop or site socket.
Specifications are subject to improvement without notice; the quotation and test certificate supplied with the machine are the governing documents. Warranty terms are stated on the quotation / invoice.
A portable machine that locks inside the pipe bore with an expanding mandrel and machines the pipe end to a set angle for welding. Because the BEVO 240 ID mounted pipe beveling machine centres on the bore, the bevel stays concentric to the pipe and the outside of the pipe stays free.
What pipe sizes can the BEVO 240 bevel?
Pipe with an inside diameter of 80 to 240 mm, about 3″ to 10″ pipe. Expansion jaw sets for this range are supplied with the machine.
How thick a pipe wall can it bevel?
Walls up to 20 mm thick, which covers standard and heavy-schedule pipe in its size range.
Which bevel angles does it cut?
Tool bits for 0° facing and 30° and 37.5° bevels come as standard. Tool bits for other angles and J-preps can be supplied on request.
What power supply does the BEVO 240 need?
A 220 V, 50 Hz single-phase supply. The motor is rated 1800 W and the spindle turns at 16 r/min.
Does the BEVO 240 cut the pipe as well?
No. It prepares the end of a pipe that has already been cut. To cut the pipe first, use a pipe cutting machine, then bevel the end with the BEVO 240.
What is the difference between the BEVO 240 and the BEVEX 63?
The BEVO 240 clamps inside the pipe and covers 80 to 240 mm pipe ID. The BEVEX 63 clamps on the outside and is made for small-bore boiler tubes, with automatic feed.
How do I get the BEVO 240 price and delivery time?
Request a quote on this page or message +91 88008 82983 on WhatsApp with your pipe size, wall thickness and material. You will receive a GST quotation with delivery time, usually the same working day.
Send us your pipe ID, wall and material — we will confirm the jaw set and quote today.
