Superior welding quality, ease of use, system flexibility, and low operating costs make this co2 welding machine the next-generation industrial welding solution. It is a 2-in-1 MIG welder that performs MIG and ARC (Stick) welding in one unit. Also, both gas-shielded MIG and gasless MIG wires are supported. The MIG welding machine is the most widely used worldwide due to its versatility and wide range of applications.
Price, delivery & technical help — get a fast response.
A 415 V three-phase inverter MIG welder that gives you 40–400 A with a separate wire feeder — built for fabrication shops that weld all day, not just for an hour.
Model: CWMIG400iJ · MIG / MAG / CO2 + Stick (MMA) · Separate wire feeder
The CWMIG400iJ is a MIG welding machine 400 amp class inverter for medium and heavy fabrication: structural steel, machine building, transport bodies, pipe and vessel work. It runs on a 415 V three-phase supply, draws a maximum of 16 kVA, and delivers up to 400 A for long seams on heavy plate.
It is a two-process machine. In MIG / MAG mode it welds with CO2, argon mixtures or gasless flux-cored wire in the 0.8–1.4 mm range. Switch to Stick (MMA) and the same power source runs electrodes for site repairs, root runs or positions where a torch will not reach. The wire feeder is a separate unit, so the power source stays near the mains point while the feeder goes to the job.
Who buys it: fabrication workshops moving up from a smaller machine that can no longer keep up, and plants that need a dependable second or third MIG station on the shop floor. If your work is mostly thin sheet and light fabrication, the MIG 250 welding machine is the better fit; if you run the thickest wire all day on heavy plate, look at the water-cooled MIG 500 system.
It is an inverter-based gas metal arc welding (GMAW) power source. Mains power is rectified, chopped by IGBT switches at high frequency, stepped down through a compact transformer and rectified again into a smooth DC welding output. Because the switching frequency is far higher than mains frequency, the control circuit can correct the arc many times per millisecond — that is what gives an inverter its stable arc and low spatter compared with an old diode or thyristor set.
Metal-transfer waveform control shapes the current during each droplet transfer, so the arc stays quiet and spatter stays low across the 16–34 V range. An arc-striking and ball-removal circuit burns the wire end clean at the finish of every weld, so the next start is reliable. Current self-adaptation holds the arc steady when the operator’s stick-out varies within 30 mm of dry extension — useful on fillets in awkward positions.
To run it you need a 415 V three-phase outlet rated for 16 kVA, a cylinder of CO2 or argon-CO2 mixture with a regulator (not needed for gasless flux-cored wire), a spool of 0.8–1.4 mm wire, and forced-air cooling clearance around the cabinet.
| Specification | CWMIG400iJ |
|---|---|
| Input supply | AC 415 V ±15%, 3 phase, 50/60 Hz |
| Max input power @100% duty cycle | 16 kVA |
| Open circuit voltage | 65 V |
| Current setting range | 40–400 A |
| Voltage setting range | 16–34 V |
| Welding current @60% duty cycle | 400 A |
| Welding current @100% duty cycle | 310 A |
| Efficiency at maximum current | 85% |
| Power factor at maximum current | 0.93 |
| Enclosure class | IP21 |
| Insulation class | H |
| Wire feed speed | 1.5–20 m/min, stepless |
| Suitable wire diameter | 0.8–1.4 mm |
| Welding torch rated current | 450 A |
| Current self-adaptation (dry extension) | Within 30 mm |
| Cooling | Forced air |
| Power source dimensions (H × L × W) | 525 × 590 × 295 mm |
| Power source weight | 56 kg |
| Wire feeder dimensions (H × L × W) | 280 × 460 × 200 mm |
| Wire feeder weight | 9.5 kg |
Shielding gas: 100% CO2 for general mild-steel work at the lowest gas cost; argon – CO2 mixture for lower spatter and a flatter bead on visible joints. No gas is needed when running self-shielded flux-cored wire.
Wire: solid ER70S-6 or flux-cored wire in the 0.8–1.4 mm range; the mid sizes are the everyday choice, the largest for the heaviest work. Fit the matching drive roll and contact tip when you change diameter.
Stick mode: general-purpose and low-hydrogen electrodes within the 40–400 A range. Contact tips, nozzles, liners and drive rolls are stocked by Cruxweld as spares.
Tell us your plate thickness and daily welding hours — we will confirm the right configuration and send a quotation.
MIG Standard Package Includes
a) High-speed wire feeder
b) ERGOPLUS24/36 10 foot MIG torch
c) Ground cable with clamp
d) Shielding gas regulator
e) Shielding gas hose
f) Extra contact tips (5) .030″”/.047″”
g) 8″”/12″” wire spool adapter
h) 415/240 VAC adapter cord
i) Drive roller
Load More
Hello
To whom it may Concern,
i would like to purchase 2 mig + 1 arc welding machine and 1 plasma cutter too so please revert me your best price list so it will easy for us to decide.
with regards,
AR ENGINEERS
Abhishek chaudhary
+91-9958605300
Okay sir.
Hello sir I want to purchase 400 amp 3 phase MIG welding machine.
Thank you for welding machine enquiry. Our team will offer you the best welding machine price.
I want to purchase mig gas,flux core and plasma cutter. Please send me the quatations.
Thank you for the interest in our welding and cutting machine. We will send you the quotation accordingly.
Plz give me price
Sure, sir, our team will do the needful.
fantastic post, very informative. I wonder why the other experts of this sector don’t notice this. You should continue your writing. I am confident, you’ve a great readers’ base already!
Resources like the one you mentioned here will be very useful to me! I will post a link to this page on my blog. I am sure my visitors will find that very useful.
Give me the best price for 400 amps mig welding machine with alluminium setting also.
Pl.. Mail me your best final price quote immediately to my email id acharya142006@gmail.com.
Also, please confirm the following in your mail.. We required total 3 nos.. At present 1no. For truck body building work.. (0.8mm to 10mm sheet weld, also angler and channel weld.. Which amps welding mechine suits for our job.. Pl.. Suggest. Also less power consumption reqd.. Per each mechine how many hp power is consumes? Pl.. Lete me know best price, delivery times (at Udupi) Karnataka and warranty and service in local..
7999499275
sir i need mig 400 machine
give me your contact and price
we need 400A MIG Welding Machine 2 in 1, please send us your lowest price with catalog by email immediately.
Dear Sir,
I need One MIG Welding Machine 400 Amp (Pulse current)
Please share the Quotation.
Warranty???
Dear Sir
We are looking for MIG welding machine….we are manufacturer of sheet metals new company and do suggest the machine and send me your catalogus and price or you can ask your sales manager to call me reg our requirements…Our Factory locating in Tirupur..
Thanks
Selvan
9677785880
Dear sir I need 400 amp mig + arc welding machine without co2 equipment.can u tell me the price plz
Interested in Automatic MIG Welding/cutting carriage. With oscillator preferred. Please send your techno commercial offer.
My name is Bharat Chandra Singh,im from SANKHABHANGA , I did matrices curation in chandua govt High school,then diploma from Mayurbhanj school of engineering Baripada
Hello sir i want to purchase 350 amp MIG machine, how much price and how much weight machine with feeder?
400A, mig welding machine price in philippine money ,
Gasless / wiht gass
I HAVE WANTS TO 400 AMPERE MIG WELDING SET TRANFORMER
i need one mig welding machine. send your price offer