The CRUXWELD FINELINE 80IC cuts mild steel, iron and galvanized sheet with its own built-in twin air compressor and runs on single phase 220 V or three phase 380 V. No separate compressor, no special power supply: take it to almost any site. Flip one switch and it becomes an MMA stick welder.
GeM Registered OEM Manufacturer · Supported Worldwide · 45+ years of welding expertise
Price, delivery & technical help — get a fast response.
The FINELINE 80IC is an 80 amp plasma cutter with a built-in twin air compressor and an MMA welding mode, in one wheeled cabinet.
Most plasma cutters need a separate air compressor, air hose and dryer before you can make the first cut, and many need three phase power. The FINELINE 80IC carries its own twin compressor inside and runs on single phase 220 V or three phase 380 V, so you plug in, clamp the earth and cut. If your shop already has compressed air, switch to External Air and use it.
Flip the Cut/MMA switch and the same machine runs stick electrodes from 2.5 to 3.15 mm, which makes this 80 amp plasma cutter a two-in-one tool for fabricators who cut and weld every day.
Many plasma cutters only run on three phase, and most also need a separate compressor. This 80 amp plasma cutter removes both limits. It works on single phase 220 V and on three phase 380 V, and carries its own twin air compressor, so whatever supply your site has, you can cut.
Run it from a single phase supply where three phase power is not available.
Connect it to the three phase supply in industrial workshops and plants.
The twin air compressor is inside the cabinet, so the site needs no air line or separate compressor.
On mild steel the FINELINE 80IC gives a clean, square cut up to 16 mm. It can sever plate up to 20 mm, with a rougher edge that may need grinding.
Plasma cutting needs a steady supply of compressed air. In the FINELINE 80IC, two air compressors are built into the cabinet of the 80 amp plasma cutter and feed the torch directly, powered by the machine itself. The 220 V lamp on the front panel shows the compressor circuit is on.
That means no compressor to buy, no tank to drain and no hose to drag across the shop. You move one machine on its wheels and start cutting.
| Usual plasma cutter setup | FINELINE 80IC | |
|---|---|---|
| Air supply | Separate air compressor | Built-in twin air compressor |
| Before the first cut | Compressor, tank, hose and regulator | Plug in, clamp the earth and cut |
| Power points needed | One for the cutter, one for the compressor | One, for the machine only |
| Taking it to site | Two machines to move | One unit on four castor wheels |
| Workshop air line | Required | Optional, with External Air |
12345Cutting and the built-in compressors both make heat. Two large fans on the rear of the 80 amp plasma cutter pull air through the cabinet and push it out through the vents, keeping the power electronics and compressors cool through long shifts.
If the machine still gets too hot, the O.C. lamp on the front lights and the output pauses until it cools down, protecting the machine.
Match the numbers on the photo to the cards below.
12345678
Not sure an 80 amp plasma cutter is the right size? See all air plasma cutting equipment, or read how plasma cutting works.
WhatsApp the material, thickness and your supply. Our team replies with the right setup and a quotation.
| Specification | FINELINE 80IC |
|---|---|
| General | |
| Model | FINELINE 80IC |
| Functions | Plasma cutting (CUT) and MMA welding |
| Input supply | 220 V single phase / 380 V three phase |
| Air supply | Built-in twin air compressor (Internal Air) or workshop air line (External Air) |
| Cutting | |
| Rated cutting current | 80 A |
| Clean cutting thickness | Up to 16 mm (mild steel) |
| Maximum cutting thickness | 20 mm (mild steel) |
| Materials | Iron, mild steel and galvanized sheet |
| Torch control | 2T / 4T |
| Gas check | Yes |
| Welding | |
| MMA electrode diameter | 2.5–3.15 mm |
| Build | |
| Display | Digital ammeter |
| Indicators | 380 V, 220 V and O.C. (overcurrent) lamps |
| Cooling | Twin cooling fans, forced air |
| Mobility | Two handles, four castor wheels with brakes |
Need an electrode holder for MMA welding, spare nozzles and electrodes or a longer torch? Ask our team on WhatsApp.
Load More
Register and take part in the drawing,
We need plasma torch tip nozzle set
Model cut70