The CRUXWELD Cut-n-Weld ProX is a portable oxy acetylene welding and cutting kit: oxygen and acetylene cylinders, regulators, a brass welding torch with cutting attachment, tips, twin hose and safety gear, packed in a poly carrier you can wheel to the job.
A cut bracket on a site, a seized bolt in a plant, a copper joint on an AC line — the jobs that need a flame rarely happen next to the main gas bank. The Cut-n-Weld ProX carries everything for oxy-acetylene work in one tote, with the hose wrapped on the carrier and the cylinders standing in it.
It needs no electric supply, so it works on a farm, a construction site, a shutdown or a roof. Set the regulators, light the torch with the striker, and you are welding, cutting, brazing or heating in minutes.
All in one carrier
Poly tote with cord wrap holds cylinders, torch and hose.
Brass torch
Welding handle plus cutting attachment with lever.
Matched regulators
CGA540 oxygen and CGA200 acetylene.
Safety included
Check valves, shade #5 goggles and striker.
Cut-n-Weld ProX, ready to roll
02 · Packing list
What Is in This Portable Oxy Acetylene Welding and Cutting Kit
The full set, laid out
×1Oxygen cylinder · 20 cu ft
×1Acetylene cylinder · 10 cu ft
×1Brass welding torch handle
×1Brass cutting torch · with cutting lever
×1Oxygen regulator · CGA540
×1Acetylene regulator · CGA200
×1Cutting nozzle · 3-101, size #1
×1Welding tip · W-1, size #2
×1Dual-line braided hose · 13 ft
×1Oxygen check valve
×1Acetylene check valve
×1Welding safety goggles · shade #5
×1Striker · with flint
×1Poly carrier tote · with cord wrap
×1Spanner
03 · Assembly
Watch the Cut-n-Weld ProX Come Together, Part by Part
Twelve parts, one carrier. The animation builds the kit in the order it goes together: cylinders into the tote, regulators and check valves on, hose to the torch, then the cutting attachment and the safety gear.
1Poly tote carrierHandle, hose reel, cord wrap
2Acetylene cylinder10 cu ft
3Oxygen cylinder20 cu ft
4Acetylene regulatorCGA200, twin gauges
5Oxygen regulatorCGA540, twin gauges
6Check valvesOxygen and acetylene
7Twin hoseDual-line braided, 13 ft
8Torch handleBrass welding handle
9Cutting attachmentWith cutting lever
10Nozzle and tipCutting 3-101 #1, welding W-1 #2
11Safety gogglesShade #5
12Striker and spannerFlint striker, spanner
04 · Four jobs
One Flame, Four Ways to Use It
Weld
Repair welds on frames, brackets and light fabrication with the W-1 welding tip.
Cut
Trim, remove and modify steel sections on site with the cutting attachment and 3-101 nozzle.
Braze
Copper and brass joints for HVAC, refrigeration and service work.
Heat
Bend, form and free seized parts with controlled heat.
05 · Regulators & torch
Matched Gauges, Brass Torch, Check Valves
Oxygen and acetylene regulators
Oxygen regulator · CGA540
Twin gauges show cylinder contents and working pressure.
Acetylene regulator · CGA200
Matched to the 10 cu ft acetylene cylinder.
Brass torch handle
Takes the W-1 welding tip or the cutting attachment.
Check valves, both lines
Help stop gas flowing back up the hose.
Using cylinders other than the ones supplied? Send us a photo of the cylinder valve on WhatsApp and our technical team will confirm the regulator fittings.
06 · Safe start
Six Steps From Case to Flame
1
Stand it up
Keep the cylinders upright and secured in the carrier.
2
Connect
Fit the regulators and check valves; connect the twin hose and torch.
3
Leak-test
Brush soapy water on every joint — no bubbles before you light.
4
Set pressure
Open cylinder valves slowly and set working pressure on each regulator.
5
Light up
Wear the shade #5 goggles and light the torch with the striker, never a lighter.
6
Shut down
Close the torch valves, then the cylinder valves, and bleed the lines.
Goggles, striker, torch and tips
07 · Where it goes
Workshops, Sites, Farms and Service Vans
Where it earns its keep
✓
Plant maintenance & shutdowns
Cut out, heat and repair without waiting for power.
✓
Fabrication & workshop jobs
Trim, bevel-heat and tack in the bay.
✓
HVAC & refrigeration brazing
Copper and brass joints on site.
✓
Automotive & general repair
Free seized parts and repair brackets.
✓
Farms, sites & remote locations
No electric supply needed at all.
Which CRUXWELD gas cutting tool?
Weld, cut, braze and heat anywhereCut-n-Weld ProX ✓
Cut-n-Weld ProX Oxy Acetylene Kit — Technical Data
PARAMETER
CUT-N-WELD PROX
Kit
Model
Cut-n-Weld ProX
Processes
Welding, cutting, brazing, heating
Fuel type
Oxygen / acetylene
Carrier
Poly tote with cord wrap
Dimensions
350 × 300 × 650 mm
Weight
18.5 kg
Cylinders & regulators
Oxygen cylinder
20 cu ft
Acetylene cylinder
10 cu ft
Oxygen regulator
CGA540
Acetylene regulator
CGA200
Check valves
Oxygen and acetylene
Torch & hose
Torch material
Brass
Torch
Welding handle with cutting attachment and lever
Cutting nozzle
3-101, size #1
Welding tip
W-1, size #2
Hose
Dual-line braided, 13 ft
Accessories
Goggles
Welding safety goggles, shade #5
Lighting
Striker with flint
Tool
Spanner
Specifications are subject to improvement without notice; the quotation supplied with the kit is the governing document. Warranty terms are stated on the quotation / invoice.
What is the Cut-n-Weld ProX portable oxy acetylene welding and cutting kit?
A complete oxy-acetylene set in one poly carrier: a 20 cu ft oxygen cylinder, a 10 cu ft acetylene cylinder, CGA540 and CGA200 regulators, a brass welding torch with cutting attachment, tips, a 13 ft twin hose, check valves, goggles and a striker.
What can I do with it?
Oxy-acetylene welding, gas cutting, brazing and heating — for example repair welds, trimming steel, HVAC and refrigeration brazing, and heating to bend or free seized parts.
Are the cylinders included?
Yes. The kit includes one 20 cu ft oxygen cylinder and one 10 cu ft acetylene cylinder that stand in the carrier.
Which regulators come with the kit?
An oxygen regulator with a CGA540 connection and an acetylene regulator with a CGA200 connection, each with twin gauges. Check valves are fitted for both gases.
Which tips are supplied?
A 3-101 size #1 cutting nozzle for the cutting attachment and a W-1 size #2 welding tip. Other tip sizes are available on request.
Does it need electricity?
No. Oxy-acetylene runs on the two gases alone, so the kit works on sites, farms and service calls where there is no power.
How big and heavy is it?
The kit measures 350 × 300 × 650 mm and weighs 18.5 kg, in a poly carrier with a cord wrap for the hose.
How do I get the Cut-n-Weld ProX price and delivery time?
Request a quote on this page or message +91 88008 82983 on WhatsApp with the quantity you need. You will receive a GST quotation with delivery time, usually the same working day.
Tell us how many kits you need — we will quote today.